do not scale from this print .405 10.29 ref .380 9.65 ref .130 3.30 .045 sq ref 1.14 (typ) 2 max sway .165 4.19 (typ) (no of positions - 1) x .165[4.19] .008[0.20] "a" "a" t-1s55-01-x-2 ipbt-08-d fig. 1 (ipbt-108-h1-xx-d shown) c c c c see note 9 (no of positions x .165[4.19]) + .053[1.33] ref .378 ref 9.60 .205 ref 5.21 .050 ref 1.27 .165 4.19 (no of positions - 1) x .165[4.19] .109 ref 2.76 c l ipbt-1xx-xx-xx-d-xx no of positions -02 thru -15 (per row) row specification -d: double (use ipbt-xx-d) plating specification -t: tin (use t-1s55-xx-t-2) lead style -h1: high power, thru hole (use t-1s55-xx-x-2, see fig.1, sheet 1) -h2: high power, surface mount (use t-1s55-02-x-2, see fig.3, sheet 3) -h3: high power. thru hole, .670" stacker (use t-1s55-05-x-2, see fig.5, sheet 4) -h4: high power. thru hole, .748" stacker (use t-1s55-06-x-2, see fig.6, sheet 4) -h5: high power. thru hole, .787" stacker (use t-1s55-07-x-2, see fig.6, sheet 4) -h6: high power. thru hole, .984" stacker (use t-1s55-08-x-2, see fig.6, sheet 4) option -ra: right angle (see fig. 2, sheet 2) [style -h1 only] -gp: guide posts (use ipbt-xx-d-gp, see fig. 4, sheet 3) -tm: matte tin (use t-1s55-xx-t-2) -02 (see sheet 5, fig.8) .424 10.77 ref .510 12.95 ref 2 max sway .165 4.19 section "a"-"a" c c c 09 01 02 t sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01[.3] 2 .xxx: .005[.13] .xxxx: .0020[.051] material: .165 double row terminal assembly by: ipbt-1xx-xx-xx-d-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing dean p 7/27/2001 5 1 sheet scale: 2:1 insulator: lcp, color: black terminal: high copper alloy f:\dwg\misc\mktg\ipbt-1xx-xx-xx-d-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. coplanarity (for surface mount): see table 2 sheet 3. 3. burr allowance: .0015[.038] max. 4. minimum terminal retention: 1 lb. 5. note deleted 6. ipbt-xx-d-xx and ipbv-xx-d parts to be molded to position, ipbe-xx-xx-d are to be cut. 7. post must be within .005[.13] of each other. 8. all pin to pin dimensions to be measured from tip to tip. 9. this number represents the number of positions per row only and is not intended to be used in position numbering. 10. all parts to be packaged in tubes except 2 and 3 pos. 2 and 3 pos parts to be layer packaged. 11. .005[.13] max cut flash. 12. after revision t of component print ipt1-xx-d-xx-x, samtec logo to appear on core #1 for positions 1 throuh 5. for positions 6 through 15, logo to appear on core #1 and the last core within the same row. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision t
"b" "b" .147 .008 3.73 0.20 .260 6.60 ref .217 .008 5.51 0.20 (see note 8) .060 1.52 90 section "b"-"b" t-1s55-04-x-2 t-1s55-03-x-2 2 max sway (either direction) 09 01 fig. 2 (ipbt-108-h1-xx-d-ra shown) (different as shown, otherwise same as fig. 1) (available only on -h1) 02 .1725 4.38 ref .394 10.00 .6861 17.43 ref in-process 1 t-1s55-03-x-2 latch .147 ref 3.73 .1475 .005 3.75 0.13 90 in-process 2 .260 6.60 ref .060 1.52 in-process 3 .260 6.60 ref 1.068 27.13 ref .688 17.48 in-process 4 t-1s55-04-x-2 -ra: right angle in-process views sheet of .165 double row terminal assembly by: ipbt-1xx-xx-xx-d-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing dean p 7/27/2001 5 2 sheet scale: 2:1 revision t f:\dwg\misc\mktg\ipbt-1xx-xx-xx-d-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
.607 15.42 ref .160 4.06 ref .327 8.31 in-process 1 t-1s55-02-x-2 t-1s55-02-x-2 90 - 4 + 0 .620 .010 .145 in-process 2 .135 ref 3.43 .160 ref 4.06 .110 ref 2.79 .424 10.77 ref (no of positions x .165[4.19]) + .483[12.27] ref (no of positions x .165[4.19]) +.240[6.10] ref fig. 4 (ipbt-108-h1-xx-d-ra-gp shown) (different as shown, otherwise same as fig. 1, 2 or 3) ipbt-08-d-gp 09 01 02 "c" "c" 2 max sway (either direction) fig. 3 (ipbt-108-h2-xx-d shown) (different as shown, otherwise same as fig. 1 01 02 09 .450 11.43 .260 6.60 ref 90 - 4 + 0 t-1s55-02-x-2 section "c"-"c" see note 2 -h2: surface mount in-process views sheet of .165 double row terminal assembly by: ipbt-1xx-xx-xx-d-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing dean p 7/27/2001 5 3 sheet scale: 1:0.470588 f:\dwg\misc\mktg\ipbt-1xx-xx-xx-d-xx-mkt.slddrw revision t 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
(see table 3) "a" .130 3.30 ipbv-xx-d ipbt-08-d t-1s55-05-x-2 fig. 5 (ipbt-108-h3-xx-d shown) (different as shown, otherwise same as fig.1) c (see table 3) "a" (no. of positions x .165[4.19]) + .033[0.84] .005 ref (see note 11) t-1s55-08-x-2 ipbt-08-d cut from ipbe-31-h6-d fig. 6 (ipbt-108-h6-xx-d shown) (different as shown, otherwise same as fig. 1) c .130 3.30 "c" ref (see table 4) "d" (see table 4) in process 1 (for h3, h4, h5, & h6 only) fig. 7 (ipbt-108-h6-xx-d-gp shown) (different as shown, otherwise same as fig. 1, 4, 5, or 6) ipbt-08-d-gp cut from ipbe-31-h6-d t-1s55-08-x-2 sheet of .165 double row terminal assembly by: ipbt-1xx-xx-xx-d-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing dean p 7/27/2001 5 4 sheet scale: 2:1 revision t f:\dwg\misc\mktg\ipbt-1xx-xx-xx-d-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
ipbt-1xx-h3-xx-d-xx shown tube: pt-1-24-04-56 plug: tp-25 ipbt-1xx-h1-xx-d-ra shown tube: pt-1-24-05-56 plug: tp-25 (2 each end) ipbt-1xx-h1-xx-d-xx shown tube: pt-1-24-01-112 plug: tp-28 ipbt-1xx-h4-xx-d-xx shown tube: pt-ipbt001-h4-h6 plug: tp-28 .050 1.27 this side, 2 pos. only (for all 2 pos.) fig. 8 (ipbt-102-h1-xx-d shown) (different as shown, otherwise same as fig. 1) ipbt-1xx-h2-xx-d-xx shown tube: pt-1-24-02-112 plug: tp-28 packaging views [parts to have position #1 loaded in same direction as arrow on tube] (see note 10) ipbt-1xx-h5-xx-d-xx shown tube: pt-ipbt001-h4-h6 plug: tp-28 ipbt-1xx-h6-xx-d-xx shown tube: pt-ipbt001-h4-h6 plug: tp-28 sheet of .165 double row terminal assembly by: ipbt-1xx-xx-xx-d-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing dean p 7/27/2001 5 5 sheet scale: 2:1 revision t f:\dwg\misc\mktg\ipbt-1xx-xx-xx-d-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|
